Glass Pool Fence Spigots: Types, Steel and Fixing on the Gold Coast

Quick answer

Glass pool fence spigots are the stainless posts that hold each frameless glass panel. Core-drilled spigots suit solid concrete and look cleanest. Base plate spigots suit timber decks and most other surfaces. On the Gold Coast, the steel grade matters as much as the type.

★★★★★ 4.8 from 51 Google reviews 3,000+ Gold Coast jobs since 2015 QBCC licence 15143274

On a frameless glass fence there is no top rail and no post. Each panel stands on a few stainless steel spigots, so they carry the whole fence. They also decide how it looks up close and how it ages in salt air.

When you're choosing spigots you make three decisions: how they're fixed, what steel they're made from, and what they're fixed into. Here's how each one works, so you can ask any installer the right questions.

Good to know: spigots also set how high the glass sits. In Queensland, the gap between finished ground level and the bottom of a pool barrier can't exceed 100mm.

1200mm

Minimum pool fence height in Queensland, from finished ground level

100mm

Maximum gap under the glass, and anywhere else in the fence

2

Ways to fix a spigot: core-drilled into concrete or bolted on a base plate

~35

Corrosion resistance (PREN) of 2205 duplex stainless, against about 25 for 316

What does a glass pool fence spigot do?

A spigot is a short stainless post that clamps the bottom edge of a glass panel. The glass sits on plastic or rubber packers inside the clamp, so glass never touches metal, and a grub screw tensions the clamp against it.

Most panels sit on two spigots. The glass supplier's specifications set how many each panel needs and how far apart they go, and the installer follows them.

Core-drilled or base plate spigots?

This is the first choice, and it depends on your surface more than your taste.

Core-drilled spigots go into a hole cut into solid concrete with a core drill, then they're grouted in place. Only a small dress ring shows at the base, so it's the cleanest look. It's also the most permanent: once it's grouted, moving a panel means a new hole.

Base plate spigots bolt onto the surface through a flat plate, and a cover hides the bolts. They work on more surfaces, including timber decks, and they're quicker to fit. You will see the plate, so the base looks a little busier.

Which spigot suits your surface?

What's under the spigot matters as much as the spigot itself. A frameless fence has nothing holding the top of each panel, so if a fixing moves even slightly, you see it as a lean along the whole run.

Solid concrete

Either type works, and core-drilled gives the cleanest finish. The installer checks the slab is thick and sound enough, and keeps fixings back from edges that could crack.

Tiles over a slab

Either type, fixed through the tile into the slab beneath. Tiles need careful drilling so they don't crack.

Pavers on sand

Neither type works on its own. Pavers on a sand bed move over time, so the fixing needs a solid base under it, such as a slab or a footing.

Timber decks

Base plate spigots, fixed into structural timber rather than just the decking boards. Many decks need extra framing under each spigot, and an older deck should have its structure checked first.

Which stainless steel suits the Gold Coast?

Stainless steel isn't one material. The grade decides how well it handles salt air, chlorine and humidity, and on the coast that matters.

PREN is a standard measure of how well stainless steel resists pitting corrosion, and higher is better. 304 sits at about 18 to 19 and suits indoor use. 316, often sold as marine grade, sits at about 25. 2205 duplex sits at about 34 to 35 and is made for coastal and pool environments.

Near the beach or on a canal, the wrong grade can show brown tea staining and look tired within about three years. Ask your installer which grade they quote, and get it in writing. Whatever the grade, rinsing spigots with fresh water now and then helps keep salt from building up.

Spigots holding frameless glass pool fence panels in a Gold Coast garden

Planning a new glass pool fence?

We get back to everyone within 24 to 48 hours, and Todd quotes every job himself.

Spigots and pool fence compliance in Queensland

Queensland uses one pool safety standard: QDC MP 3.4, read with AS 1926.1-2007. Spigots affect three of its key rules.

The barrier must be at least 1200mm high, measured from finished ground level. The gap from finished ground level to the bottom of the barrier can't exceed 100mm, and no gap anywhere in the barrier can exceed 100mm, including between panels.

Ground levels change. A new garden bed or extra paving can cut the height of a compliant fence, so check it whenever the landscaping changes. Selling or leasing? Our guide to the pool safety certificate in QLD explains how fences are inspected.

What should you ask your installer?

Four questions tell you most of what you need to know about how a fence will be fixed.

1

Which fixing method?

Core-drilled or base plate for your surface, and why that one.

2

Which steel grade?

316 or 2205 duplex, written on the quote.

3

What is it fixing into?

A slab, a footing or structural timber, and whether it's solid enough. On a deck, check they're fixing into the frame, not just the boards.

4

Where will the glass sit?

Where the bottom of the glass will sit once the paving is finished, and whether you'll get a Form 15 for the barrier.

Frameless glass pool fence beside a canal-front pool on the Gold Coast, with Surfers Paradise high-rises behind

Once the spigots are right, the rest of the fence follows. See our pool fencing on the Gold Coast options, or read how we install a glass pool fence.

Glass pool fence spigot FAQs

What's the difference between core-drilled and base plate spigots?

Core-drilled spigots are grouted into holes cut in solid concrete, leaving only a small ring visible. Base plate spigots bolt onto the surface through a plate, so they suit more surfaces, including timber decks.

Are 316 stainless spigots OK on the Gold Coast?

316 is common, but near the beach or a canal it can tea-stain. 2205 duplex has much higher corrosion resistance (a PREN of about 35, against about 25), so ask your installer which grade they quote.

Can glass pool fence spigots go on a timber deck?

Yes, with base plate spigots fixed into the deck's structural timber, not just the boards. Extra framing is often added under each spigot.

Can spigots be fixed to pavers?

Not to pavers laid on sand on their own, because they move. The fixing needs a solid base under it, such as a concrete slab or a footing.

How high off the ground can the glass sit?

In Queensland, the gap between finished ground level and the bottom of a pool barrier can't exceed 100mm, and the barrier must be at least 1200mm high.

Not sure which spigots suit your pool?

Book a free on-site quote. Todd measures every job himself and checks what you're fixing into before he quotes.

TM

Written by Todd Mehlhopt, founder of Gurus of Glass

Todd started Gurus of Glass in 2015 and has quoted and installed frameless glass pool fences across the Gold Coast ever since, with more than 3,000 jobs completed. This article was checked against QBCC guidance in November 2026. It's general information, not legal advice, so check the QBCC website or speak to a licensed pool safety inspector about your property.

Related Posts

Free On-Site Quote

We will get back to you within 24 to 48 hours. No obligation, and no chasing if you decide to go another way.